# How Many Outlets Can I Run Off A 20 Amp Breaker?

## How many watts can you run off a 20 amp breaker?

2,400 watts20-amp 120-volt circuit: 20 amps x 120-volts = 2,400 watts..

## Can I mix 12 gauge and 14 gauge wire?

Anyway, the first subject is a bit touchy because it makes it difficult to perform an inspection when all of the wires coming into the panel are 12 but many of the circuits have 14 in them too. There is nothing against code mixing wire size for these circuits as long as the OCPD matches the smallest wire.

## How far can you run 12 gauge wire?

The following are the maximum lengths of cable you can use while still maintaining a 3 percent voltage drop for the given wire size (AWG) and circuit voltage….For 120-volt circuits:14 AWG50 feet12 AWG60 feet10 AWG64 feet8 AWG76 feet6 AWG94 feetOct 20, 2019

## Do outdoor outlets need to be on their own circuit?

That being said, no, outdoor outlets are not required to be on a separate circuit. They do need to be protected by a GFCI which can either be a GFCI breaker or the familiar “outlet with buttons” wall box mounted unit.

## Can 14 gauge wire be used for outlets?

Yes you may use No. 14 AWG Cu wire for outlets but the Circuit Breaker to protect the circuit should be only 15A. Do not use 20A Circuit Breaker for this circuit. … The circuit should not have more than 10 receptacles.

## Should I use 12 or 14 gauge wire?

14-gauge wire is the smallest allowed for the permanent wiring of a circuit. It is rated as able to carry up to 15 amps of current. 12-gauge wire is the next size larger and is allowed to carry up to 20 amps.

## How many outlets can you put on a 14 2 wire?

14–2 wire is allowed for a 15 Amp circuit, and at 120 Volts, 15 Amps x 120 volts = 1800 volt-amperes. So that would allow ten (10) receptacles, you would probably derate that to eight (8) for an 80% safety factor.

## How many LEDS can be on a 20 amp circuit?

40 lightsYou can put up to 40 lights (based on 50 watt light) on a 20 amp breaker.

## How many outlets can a GFCI protect?

A standard GFCI will protect up to 20 amps, drawn from any combination of receptacles, either the built-in one or any number of additional ones connected to its load terminals.

## How many outlets can be on a breaker?

By rule of thumb you would stick with 8 to 10 outlets and or lights per breaker.

## How many outlets can I put on a 15 amp breaker?

Generally, homes have eight to 10 outlets on a 15 amp breaker but not all are used at the same time. Lights and outlets are normally wired on separate branch circuits, which means that the lights will be protected by a separate circuit breaker to the one which protects the outlets.

## How many LED lights can I put on a 15 amp circuit?

Each CFL or LED bulb typically gives the same amount of light as a 60-watt incandescent bulb while drawing 10 watts or less, which is equivalent to a current draw of 1/12 amp. Thus a 15-amp circuit can safely control 180 or more fixtures that use CFL or LED bulbs.

## How much can you put on a 20 amp circuit?

For a 20-amp circuit, the load limit is 2,400 watts.

## How far can you run 12 gauge wire on a 20 amp circuit?

The total circuit would be about 60 -70 feet in length. It would only be supplying about 5 outlets and one light. It would be a light load, running small things, no heaters or med/large equipment. #12 provides reasonable performance up to about 100′ with general loads like you describe.

## Can you daisy chain outlets?

Electrical receptacles have two pairs of terminals so that you can daisy-chain multiple receptacles on a single circuit in an existing house. … That way, if one of the breakers blows, you’ll still have a live outlet to use.

## Can I use 12 gauge wire on a 15 amp circuit?

However, 12-gauge wire is acceptable on both 15- and 20-amp circuits, so some electricians use it exclusively when wiring a house.

## What happens when you put a 20 amp receptacle on a 15 amp circuit?

If your question is “can I connect a receptacle rated for 20 amps to a circuit designed for 15 amps?”, the answer is yes, because the receptacle can handle more current than the circuit is rated for. If you exceed 15 amps, the breaker will blow, and protect the receptacle.

## How many 15 amp receptacles can be on a 20 amp circuit?

Table 210.21(B)(3) also shows that a 15 amp receptacle can be installed on a 20 amp circuit that serves 2 or more receptacles. Commentary following 210.21(B)(2) in the handbook clearly states that 15 amp receptacles are permitted on a 20 amp circuit.

## How many outlets can you run on a 12 2 circuit?

For general use receptacles, In commercial buildings it is limited to 180VA per duplex or single receptacle, therefore on a 12/2 Romex cable not otherwise subject to ampacity derating and protected by a 20 amp circuit breaker, that would allow a maximum of 13 receptacles.

## Can lights and outlets be on the same circuit?

Basic answer to your question of can a mixture of lights and receptacles be installed on a single circuit is yes. … In your case it is okay to install a receptacle alongside the switch. However you need a neutral as well as a hot wire which you may not have. Test to see if you have a neutral with a test light or meter.

## Can you use 14 gauge wire on a 20 amp breaker?

6 Answers. I would say 14 gauge wire anywhere on a 20 amp circuit is not OK. The purpose of the breaker is to cut off power before the wiring overheats. If you plug in several devices on an outlet that total 20 amps, you will exceed the safe working capacity of the 14 gauge wire without tripping the breaker.